reMarkable Paper Pro Move · Troubleshooting
The reMarkable Paper Pro Move won't turn on or is frozen
The screen is blank, stuck on the startup logo, or frozen and not responding. Most cases are a flat battery or a software hang that a forced restart clears.
Symptoms
- Pressing the power button does nothing and the screen stays blank.
- The device is stuck on the reMarkable logo or the loading dots.
- The screen is frozen and touch and the Marker do nothing.
- It will not wake from sleep.
Before you start
- Use a charger and cable you know work.
- Give any charging attempt at least 30 minutes before deciding it is not working.
- A forced restart does not erase notebooks; a factory reset or re-provisioning does.
Which fix do you need?
What is the device doing?
- Completely blank, no logo, no light Charge it first, then force a restart
- Stuck on the logo or the loading dots Force a restart; if it recurs, let it charge fully and retry
- The screen is on but frozen A long power-button hold clears the hang
- It started after a firmware update or community software Recovery may need reMarkable support or re-provisioning
Most common cause
The most common cause is a fully drained battery — the Move has a smaller battery than the bigger reMarkables, so it drains faster if the front light was left on, and a flat device needs time on the charger before it responds. The next most common is a software hang, which a long power-button hold clears.
Fixes
Fix 1 Charge it, then force a restart
A deeply discharged Move gives no response until it has taken on some charge. Only after charging is a forced restart worth trying.
- Plug the device into a wall charger with a known-good USB-C cable and leave it for at least 30 minutes, longer if you can. No charging indicator may show at first.
- With it still plugged in, press and hold the power button for about 10 to 15 seconds. The screen blanks and then shows the startup logo.
- Release and let it boot. After a full drain this can take a couple of minutes.
- If there is still nothing after an hour on a proper charger and a power-button hold, try another cable and charger before assuming a fault.
Fix 2 Force a restart for a hang or a stuck logo
If the screen is lit, the device has power but the software has stopped. A long power-button hold forces a clean restart.
- Press and hold the power button for about 10 to 15 seconds until the screen changes and the logo appears, then release.
- Let it finish. A frozen session is usually back to normal afterwards.
- If it hangs on the logo or the loading dots again, plug it into a wall charger and leave it for an hour, then repeat the hold — a device very low on charge can stall partway through boot.
- If the logo hang repeats after a full charge, go to Fix 3.
Fix 3 Recover a device that will not boot after an update or modification
A firmware update that went wrong, or community software on an unsupported firmware, can leave the device unable to start normally. The Move's newer platform is more prone to this than the reMarkable 2.
- If you have not modified the device, contact reMarkable support with the symptoms and your serial number. A genuine boot failure on an unmodified device is a warranty matter.
- If you enabled developer mode or installed community software, the supported path back is to re-provision the device — reMarkable's recovery process, or turning developer mode off, both of which wipe it. Notebooks that had synced to your account come back afterwards.
- Follow a community recovery guide only if it is matched to your exact model and firmware, and only if you are comfortable with the risk.
Undo / recovery
A forced restart leaves your notebooks in place. Re-provisioning or a factory reset erases the device, but notebooks that had synced to your reMarkable account come back after you sign in again. Before any reset, if the device is reachable at all, get it onto Wi-Fi and let it sync, and export anything critical as a PDF.
Related guides
Charge it and hold the power button for 10 to 15 seconds first. A stuck logo that repeats usually just needs a longer charge before it can finish booting; a device that will not start after an update or a modification needs reMarkable’s recovery process or support.